Home
Up
Specials
New Products
Glass Machines
Lapidary Supplies
Information
Catalog Request
Intro to Lapidary
Intro to glass beveling
About us

These motors are U.L. listed with 3-prong switch cord. 
IMPORTANT: State motor model, pulley and belt size when ordering.
DANGER: Thermal protected motors will stop if overloaded. If motor stops, shut-off electrical supply switch, otherwise motor will restart automatically. 

110V, 60 HZ Motors
MTR004--1/20 HP, 1550 RPM with studs mount, Shipping wt. 6 lbs. $ 110.00
MTR618--1/18 HP, 1550 RPM with studs mount, Shipping wt. 6 lbs. $ 115.00
MTR580--1/10 HP, 1550 RPM, thermal protected with small base mount. Shipping wt. 8 lbs. $ 130.00
MTR282--1/3 HP, 1725 RPM, NEMA 56 base with pulley & belt. Shipping wt. 20 lbs.  $ 154.50
MTR853--1/3 HP, 1725 RPM, NEMA 56 base,  with pulley & belt. Shipping wt. 27 lbs. $ 251.00
*MTR199--1/2 HP, 1725 RPM, NEMA 56 base, thermal protected, pulley & belt. Shipping wt. 27 lbs. $265.00
*MTR376--3/4 HP, 1725 RPM, NEMA 56 base,, thermal protected, pulley & belt. Shipping wt. 30 lbs.  $ 316.00
MTR321--1 HP, 1725 RPM, NEMA 56 base,  thermal protected, pulley & belt. Shipping wt. 35 lbs. $ 339.00
MTR922--1 HP, 1725 RPM, NEMA 56 base,  No thermal protection, pulley & belt. Shipping wt. 35 lbs. $ 366.00
* Indicates 50/60 hz motor.

220V, 50 HZ Motors
MTR001--1/20 HP, 1550 RPM with studs mount. Shipping wt. 6 lbs. $ 120.00
MTR552--1/18 HP, 1550 RPM with studs mount. Shipping wt. 6 lbs. $ 125.00
MTR409--1/3 HP, 1425 RPM, NEMA 35/56 base, pulley & belt. Shipping wt. 20 lbs. $ 225.00

Replacement Inline Switch Cord for all 110v motors
 Product may vary from picture.

$ 18.00   

Replacement Bearings

RUBRS1--Bearing with grommet for 6" Combo Units $ 37.00
LRCS16--Bearing with grommet for 8" Combo units $ 39.50
SRC160--Bearing with grommet for Vertical Arbors $ 45.00
SRF160--Bearing with grommet for Vertical Arbors 5/8" Arbor Hole. For 268 Tumbler $ 32.00
SRF161--Bearing, grommet & flange for 16" Horizontal Laps $ 65.00
SLS700--Bearing for 700 Series Saws.  Need to replace in pairs. $ 27.50

Ball Bearing Pillow Block
Precision ball bearing pillow block neoprene-sealed and greased for life. Mounting hole spacing 3 3/8". Comes in 1/2, 5/8, 3/4 & 1" bore. 
Specify size.
PBB025--Pillow Block $ 35.70

Bronze Bearing Pillow Block
Self-aligning bronze bearing with large oil reservoir and thick rubber mounting grommets. Mounting hold spacing 3". Comes 1/2, 5/8, 3/4, & 1" bore.
Specify size.
BPB531--Pillow Block $ 16.85

Large Shaft Adapters

1" outside diameter adapter with left or right hand nut thread. Has 1 1/2" inside width for wheel or buff mounting. Comes in 1/2, 5/8 or 3/4" bore.  Made In USA By Covington's
Specify smooth bore size and left or right for nut thread.
LSAR35--For right side applications $ 23.00
LSAL35--For Left side Applications $ 23.00

CHOOSE TYPE AT CHECKOUT

 

1/2" Machined Shaft Adapters

Shaft adapter converts 1/2" shaft to 1"-14RH or LH.  Made In USA By Covington's
Specify smooth bore size and left or right for nut thread.
MSAR05--For right side applications $ 12.50
MSAL05--For Left side Applications $ 12.50
 

 

 

Small Shaft Adapters

Wheels having a 1/2” arbor bore and up to 1” thick are retained in the 1/2” - 20 threaded shaft section between the two 1 1/2” flanges. Overall length 3 1/2”. Specify left or right hand thread when ordering and 1/2" or 5/8" arbor hole.
SSAR04--For 1/2" diameter shaft, Right side application $ 12.25
SSAL06--For 1/2" diameter shaft, Left side  applications $ 12.25

Tapered Spindles

Made from aircraft aluminum and machined to very tight tolerances. These tapered spindles are not your everyday low quality spindles.  They are U.S. made.   Used to hold wheels such as muslin or felt buff.  Buffs are screwed onto taper until tight.  Made with either right or left handed threads. Smooth bore spindle is secured to smooth shaft with set screw.
$ 13.50 each for any type/size  Choose size/type at checkout
1--For 1/4" shaft (right) $ 13.50
2--For 1/4" shaft (left) $ 13.50
3--For 3/8" shaft (right) $ 13.50
4--For 3/8" shaft (left) $ 13.50
5--For 1/2" shaft (right) $ 13.50
6--For 1/2" shaft (left) $ 13.50
7--For 5/8" shaft (right) $ 13.50
8--For 5/8" shaft (left) $ 13.50

   

LAPIDARY EQUIPMENT
ARBORS BEAD MILLS BELT SANDERS BOOKS
CAB KING CABBER CARRIAGE SLAB SAW KITS COMBO UNITS DELUXE TUMBLERS
DIAMOND BLADES DIAMOND COMPOUNDS DIAMOND DISCS DIAMOND DRILL BITS
DOP STOVES/WAX DRUM SANDER ELECTRIC MOTORS ESTWING TOOLS
EXPANDO DRUM UNITS FLANGES FOREDOM CRAFT KIT GEM DRILLS
GRINDER-POLISHER GRINDING WHEELS GRITS HAMMERS
HORIZONTAL LAPS JEWELRY BUFFERS JEWELRY WIRE BENDER KOOLERANT
MAXI LAPS NEEDLE FILES OPTIVISOR PLIERS & CUTTERS
POLISHING POWDERS PULLEYS ROCIPROLAP ROLLING TUMBLERS
SANDERS / WET-BELT SANDING DISC & BELTS SILVER SOLDER SLAB SAWS
SLAB SAW OIL SPHERE MACHINES SPLASH GUARDS TEMPLATES
TRIM SAWS TUMBLERS VIBRATING LAPS VIBRATING TUMBLERS
VINYL APRONS WIRE SAWS MANDRELS

   

GLASS MACHINES
CORK & FELT POLISHER GLASS BEVELERS GLASS ENGRAVER GLASS LATHE
GLASS SAWS & BLADES GLASS SMOOTHER & KITS ROCIPROLAP SANDERS / WET-BELT

Covington® Engineering Corporation
U.S. Toll Free (877)793-6636  Outside U.S. 909-793-6636  Fax 909-793-7641
Email us at sales@covington-engineering.com
715 West Colton Avenue -- P.O. Box 35 -- Redlands, CA 92373